Shiro Cordless Telephone SD8141 User Manual

 
Pag.  
Pag.  
. 15  
Index  
SD8141  
1
1
1
3
3
4
5
6
7
7
7
7
.
PABX code  
Call barring  
Disabling call barring  
Accessories  
Technical data  
.
.
. 15  
. 15  
. 16  
. 16  
. 16  
. 16  
. 17  
. 17  
. 17  
. 17  
. 18  
A glance guide tothebuttons on your  
handset  
.
LCR (Least Cost Routing)  
How to enable / disable LCR  
How to set LCR “Primary”  
How to set LCR “Routable”  
How to set LCR “Special”  
How to set LCR “Others”  
Multi handset configuration  
Subscription of optional handset  
How to de-subscribe a handset  
.
K e y a n d s y m b o l s d e s c r i p t i o n  
.
A glance guide to the buttons on the base  
.
Installationandset-up  
AC/DCadaptorinstallation  
Phone line connection  
Battery installation  
Battery charging  
Coverage range  
Precautions  
Handset On/Off  
Beforeusingtheunit, check  
.
.
.
7
7
8
8
8
8
8
8
.
.
.
.
.
Intercommunication between handsets . 18  
Call transfer between handsets  
Conference call  
Multi base configuration  
. 18  
. 18  
. 18  
How subscribe handset to anotherbase . 19  
__  
.
Base search  
BabySitting(roommonitor)  
. 19  
19  
To make a call_________________________.  
.
.
8
9
9
9
9
9
9
9
Pre-dial  
How to answer incoming call  
Automatic answer  
Adjustment of receiver volume  
Microphone mute  
Put on hold the caller  
Last number redial  
One of the 10 last numbersredial  
R key (recall)  
Paging handset  
.
.
.
.
.
.
.
.
.
.
.
.
Factory default setting  
- Phone book: empty;  
- Called numbers list: empty;  
- Caller ID list: empty;  
- LCR router: disabled with below settings:  
Primary= empty;  
Others=empty;  
Routable*=empty;  
Special*= empty  
- Handset name:HANDSET;  
- Handset ringing volume: 4;  
- Handset external ringing tone : 1;  
- Handset internal ringing tone .: 5;  
- Confirmation beep: enabled;  
- Timer: enabled;  
- Date & Time: present on display, enabled  
automatic setting;  
- Alarm: disabled;  
9
9
10  
10  
10  
10  
11  
11  
11  
11  
12  
12  
12  
12  
12  
13  
13  
13  
13  
13  
13  
14  
14  
14  
14(2)  
Out of range indication  
Battery level indication  
Usingearphone  
.
Calleridentify  
____  
.
.
.
.
.
.
Navigation method into menu  
Date & Time setting  
Keypad lock  
Warning and confirmation tone On/Off  
Handset ringer volume setting  
Handsetringertonesetting  
Base ringer volume setting  
Base ringer tone setting  
Ringer priority setting  
Timer enabling / disabling  
Replace handset name  
Language display setting  
Phone book  
To modify entry memory  
To delete entry memory  
To delete all entry memory  
To call entry memory  
.
- Base ringing volume:5;  
- Base ringing tone: 1;  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
- Ringing priority: disabled;  
- Call barring: disabled;  
- PIN Code: 0000;  
- Dialling mode: Tone (DTMF);  
- PABX pause: disabled;  
- Baby sitting; disabled;  
- Display language: English;  
- Handset subscribed: only handset 1;  
- Receiver volume: level 3;  
*After resetting, remember to input the special and  
routable prefix on LCR router (seeparagraph LCR”).  
To store a number fromthe redial list  
Alarm setting  
PIN code changing  
Dialling mode setting  
 
2
A glance guide to the buttons on your handset.  
The handset  
Earpiece  
Listening  
Display  
See page 4.  
MEM button  
press to make  
calls to numbers  
stored in memory  
FLASH button  
you will need this  
if your phone is  
connected to a PBX,  
or if you use Call-  
waitting servies  
OK button  
press during programming  
to confirm your selections.  
Press and hold to switch the  
handset off.  
MENU button  
Press to start and end the  
programming menu.  
SD 8141  
02899832620  
PHONE button  
press to begin, answer and  
end a telephone call.  
C (CLEAR) button  
Press during programming to  
move back to the previous  
menu option, or to clear digits  
one by one from the display  
MUTE button  
REDIAL button  
press to display the last 10  
numbers you dialled.  
UP and DOWN buttons  
Press during  
Press during a call to mute  
the microphone so the  
other person could not hear you.  
programming to  
move through  
the menu.  
Press during  
a call to change  
the volume  
in the earpiece.  
RD  
INT button  
Press to make an  
intercom call if you  
have more than one  
handset registered to  
ther base unit.  
INT  
/
(Caller Display)  
Press to display details of  
people who have called you.  
SPEAKERPHONE button  
press to turn the speaker-  
phone on and off.  
Charge contact  
Charging batteries  
Microphone  
pick up the voice  
Before you can use the handset to make  
calls you will need to fit and fully charge  
the batteries, as described on pages 6 to 8.  
Please read the notes on page 5 before you  
install the base unit.  
 
3
Key and symbols description  
Handset:  
: Hook switchkey;  
INT : Intercomkeybetweenhandsets;  
: phone book access key and flash key ;  
\
: mute key, delete key and Menu exit key ;  
: Menuaccess key, confirmationkey, handsetOn-Off;  
: Rediallistkey/up arrow;  
RD  
: caller identification list access key and down arrow;  
: hands freespeakerphonekey;  
Display symbols:  
: the handset is in thecoverage area of the base;  
: Menuaccess;  
: phonebookaccess;  
: phone call is in progress (xmeans microphone mute enable);  
: handsetringerdisabled;  
: baby sittingfeatureenabled;  
:not answered call present in thecaller ID list;  
:Hands freespeakerphoneis in use;  
: keypadis blocked;  
: battery levelindication;  
Base LED:  
NUSE/  
NEW CALL  
: phone conversation isin progress, when is blinking reflect unanswered calls;  
: handsetis in thecradle;  
P
: paging key to call handset;  
 
4
A quick guide to the buttons on the base.  
The Base  
Incoming Call Light  
Charging Light  
Page Button  
New Call / In Use  
The headset jack  
The headset jack let you  
use the handset**(optional).  
Start by plugging  
it into the bottom of  
the handset as shown.  
** You can purchase the handset from our office or purchase a mobile phone handset(motoroXX type).Make sure  
the volume is turned up as the mobile phone handset have different power setting.  
The belt clip  
If you are using your SD 8141,  
you may wish to fit the belt clip to  
make the handset easier to  
carry.  
Fit the belt clip  
as shown,  
making sure it  
clicks firmly  
into place  
 
5
Installing and using your SD 8141digital cordless telephone  
Installation and Setting Up  
1
Choose a suitable site for the base unit. Make  
sure it is not near to another telephone or  
other electrical equipment  
DC 9V  
2
Plug the main power lead and the  
telephone line cord into the back of  
the base unit  
3
Plug the power adaptor into a 230 V AC,  
50 HZ main socket, with the switch on the  
socket set to OFF  
The SD 8141 base unit must be  
used with the power adaptor  
supplied with the unit. Using any  
other adaptor will result in  
non-compliance with En60950.  
This will invalidate any  
approval given to this apparatus.  
4
5
Switch on the power at the socket  
Fitting the batteries in the handset  
Insert the rechargeable batteries as shown,  
making sure they are firmly in place  
Fit the battery compartment cover,  
sliding it until it clicks firmly into  
position  
** PleaseDmoawkensuloreathdatfroonlmy REWCHwARwG.ESABoLEmbaatnteurieaslasr.ecuosemd,. All Manuals Search And Download.  
6
otherwise the warranty will be void.  
AC/DC adaptor installation  
Connect the plug of the adaptor to the power jack  
back, and connect it to the220V socket.  
of the base set located at the  
Phone line connection  
Connect the plug of the telephone line cord to the jack of base set  
back, and connect it the line socket.  
located at the  
Battery installation  
1- Remove the battery door;  
2- Insert the batteries into the compartment;  
3 - Close battery door.  
IMPORTANT: The Nichel-Metal Hydrate battery, when exhausted, must be recycled or  
disposed properly.  
Battery charging  
Put the handset onto the cradle. Charge at least 10 hours when the battery is totally  
discharged. The light indicator will light up to show that the handset is in charging  
mode. When completely charged, this light indicator will remain on.  
Coverage range  
The coverage area could be affected from manifold situations. The indication of 300m  
outdoor and 50m indoor serves as a guide which is obtainable only in a optimal  
conditions of propagation of the signal. However for a better coverage it is advisable to  
install the base set in a central position of the building within where the cordless phone  
be used.  
Precautions  
1) Read this manual before using this phone.  
2) Avoid direct exposure to solar rays and/ or fronts of heat, as well as to avoid the  
installation in damps places and/ or dusty.  
3) Do not support objects on the cables and/ or on the phone.  
4) Do not use adaptor and/ or batteries diverged from those specified on this  
instructions manual or however from those in endowment.  
5) In case of storms, disconnect the phone from power and phone lines.  
6) Clean by using a slightly dampened cloth. Do not use alcohol, solvents, abrasives,  
etc.  
7) Do not effect reparations alone. Tampering and/ or uses not in conformity with those  
described on the instructions manual will render the warranty void.  
8) Shiro Corporation declines any responsibility in case of improper uses or  
manipulations not conform with the instructions as described in this manual.  
 
7
Handset On/Off  
Press  
key to switch handset On or put it in the cradle for charging. It will switch On  
automatically.  
To switch Off, hold and press  
key for approximately 2 seconds.  
Before using the unit, check:  
1) The installation wasperformed properly;  
2) The batteries havebeen charged properly;  
3) The LCD display"OFF" (press  
key to switch on handset incase it is off);  
To make a call  
1) Press key for dialing tone (the baseLED indicator will light up);  
2) Dial the desired number;  
3) Press  
will be off).  
key or put the handset in the cradle to end a call (the base LED indicator  
NOTE: Pressing  
cease the line.  
At the end of eachcall, the LCD screen willdisplay the talk time durationfor about 5  
key will enable the hands free speaker phone. This key cannot  
seconds.  
Pre-dial  
1) Dial the outgoing number (press  
deleted. Alternatively press and holdto delete full number) ;  
2) Press key to send a call. The number will be dialout automatically.  
key if there is an error. The last digit will be  
How to answer incoming call  
1)Press  
2) Press  
key when handset rings;  
key to answer directly with thehands free speaker phone.  
Automatic answer  
When the handset is inthe cradle, lift to answer a call.  
ATTENTION: If you have Caller ID service, the automatic answer will be disabled. You  
can decide whether to answerthe call.  
Adjustment of receiver volume  
During a phone conversation, press  
or  
key to adjust the receiver volume.  
RD  
Choose from 5 volume levels. 1 being the lowest and 5 the highest. The volume  
indication will disappear fromLCD screen after 3 seconds.  
 
8
Microphone mute  
During a phone conversation, press  
microphone will be disabled, but you will still be able to hear the caller. Press  
to restore a phone conversation.  
key, the LCD screen will display  
. The  
again  
Putting the caller on hold  
During a phone conversation, press the INT key. The other party will hear beeping  
sound. Press INT key again to restore thephone conversation.  
Last number redial  
To dial the last dialled number, take phone line by  
last number will be automatically dialed out.  
key, then press RD  
key. The  
One of the last 10 numbers redial  
SD 8141 automatically store the last 10 dialled numbers. To call one of them, press  
RD  
key, and search through the list by  
or  
keys until the LCD screen  
RD  
display the desired number.  
R Key (recall)  
\
Pressing  
key during a phone conversation allows you to access to the  
supplementary service of the network (example, the call waiting if subscribed with the  
network operator).  
Paging handset  
Pressing P key of the base, the handset will ring. This function can be useful, for  
example, to locate the handset. Press any key on the handset toend a paging call.  
Out of range indication  
Please note that the conversationwill be cut off ifyou are far from coveredrange of the  
base set. The symbol  
willblink on theLCDscreen.  
Battery level indication  
LCD will display 4 battery levels:  
displayed  
charging.  
= full;  
, , it indicates that the battery is flat. Put handset in the cradle for  
middle;  
= low. If the symbol is  
Using earphone  
Sd8141 is equipped with a 2.5mm jack where it can be connected to one standard  
earphone typically used for mobile phone.  
ATTENTION: select the proper earphone making sure it is the standard type  
 
9
Caller Identity (workable only if subscribed withnetwork operator)  
SD8141 is able to display the caller number. If the caller number is stored into the  
phone book, the name will be displayed. It stores the last 20 calls automatically (the  
symbol  
answered). To see the caller list, press  
content. Pressing when the number is displayed, will reflect the date and time of  
thecall. Ifyou press again key, display willshow "SAVE? ".Ifyou press key  
again, you can store the call number on the phonebook. Input the location name of  
on LCD screen and the light  
on the base will blink when the call is not  
key and then keys to list the  
RD  
this number and press  
number.  
However, if you wish to delete the caller number, press  
key to confirm the name and press  
key to confirm the  
key when display shows  
"SAVE? ". The display will show"DELETE". Confirmby pressing the key.  
ATTENTION: Date and timeare available only onPSTN lines and noton ISDN lines.  
If you like to call the number reflected on the LCD screen, press  
dialled out automatically.  
key and it will be  
Navigation method into menu  
SD8141 is endowed with anintuitive system of listed menuand sub-menu. The  
Key allows input into the main tree of menu. Pressing RD  
menu tobelisted. Pressing key allows input to thesub- menu.  
Pressing the key allows you to return to the previous menu. Press and hold the  
or  
keys allow the  
same key allows you to escape from menuand come back in the stand-by mode.  
NOTE: For the subsequent steps, the procedure to input the main menu will not be  
mentioned anymore .  
Date & Time setting  
SD8141 is equipped with automatic clock setting system. If you are using it with an  
analogue line PSTN (not ISDN) with the caller ID enabled, the clock will be set  
automatically when there is an incoming call. Otherwise, the clock have to be set  
manually with the following procedure:  
- under sub- menu "HANDSET", search for "CLOCK". Enter this menu and select "SET  
key. Set month  
key. Setdate.  
CLOCK". Set hours then press  
thenpress  
key . Set minutes then press  
Press  
to confirm. To auto setting, go to sub-menu, "CLOCK", search for  
and set"YES "if you like the auto setting orselect"NO". Press  
to confirm. This will automatically set the handset’s date and time based on the  
FSK CID of the PSTNnetwork.  
AUTOMATIC”. Select  
Under the sub- menu, go to "CLOCK ", press "OK ". If you prefer not to display the clock  
onto the LCD Screen, press "OFF". Press toconfirm.  
 
10  
Keypad lock  
To lock the handset keypad:  
- enter sub-menu "KEY LOCK" which is in the main menu. Choose "YES " (lock enabled) or  
"NO" (lockdisabled), press  
To unlockkeypad, press  
toconfirm.  
keythreetimes.  
Warning and confirmation tone On/Off  
There will be a warning beep when the phone is Out of range, Low Battery,  
Confirmation at Programming and Key Click. These tonescan be disabled by:  
- enter sub- menu "HANDSET" which is in the main menu, search for "TONES". Enter this  
menu and search for the tone you wont to disable or enable between "KEY ,RANGE,  
LOW BATT " and "CONFIRM", press  
disabled), press toconfirm.  
, select "YES " (tone enabled) or "NO " (tone  
Handset ringer volume setting  
You can set up to 4 different volume levels or disable the handset ringer (handset will  
not ring). To set, follow this procedure:  
- enter sub-menu "HANDSET" which is in the main menu, search for "RINGER". Select the  
desired volume level by RD  
symbol will be displayed on LCD screen). Press  
or  
keys (included for ringer off -"VOL OFF",”,  
to confirm.  
Alternatively, with an incoming call, adjust the ringer volume directly by pressing RD  
or keys.  
Handset ringer tone setting  
Set up to 5 different ringer tones. You can also set a different ringer tone for incoming  
call and intercom call. To set, follow as below:  
- enter sub-menu "HANDSET" which is in the main menu, search for "EXT RING" for the  
incoming call, or "INT RING" for the intercom call. Press  
the or keys. Press to confirm.  
and set the desired tone by  
RD  
Base ringer volume setting  
Set up to 5 different volume levels or disable ringer (base will not ring). To set, follow as  
below:  
- enter sub-menu"BASE" which is in the mainmenu, search for"RINGER".  
Press  
or  
and select"VOLUME". Press and set the desired volume by RD  
keys (included for ringer off - "VOL OFF"). Press to confirm.  
 
11  
Base ringer tone setting  
Set up to 5 different ringer tones. To set, follow as below:  
- enter sub-menu"BASE" which is in the mainmenu, search for "RINGER".  
Press and select"MELODY". Press  
keys. Press toconfirm.  
and thedesiredtoneby RD  
or  
Ringer priority setting  
Choose the ring setting between base or handset (or handsets) and the number of  
times the phone will ring theother unit. To set, follow as below:  
- enter sub-menu"BASE" that is on the mainmenu, then select "RINGER". Press  
RD  
and select "PRIORITY". Press  
Select the unit to ring first. Press  
rings the other unit will ring. Press  
and select "SET UP". Press  
follow by  
keys, specify after how many  
to confirm. The LCD screen will display "PRIORITY",  
key.  
RD  
and  
or  
press  
and select between"YES" or"NO "to enable or disable the ringerpriority.  
Timer enabling/disabling  
At the end of each call, the conversation time will be reflected on the LCD screen  
display. You can disable or enablethis function using the following:  
- enter sub-menu"HANDSET" which is in the mainmenu, search for"TIMER".  
Press  
confirm.  
and select between "YES " and "NO" to enable or disable timer. Press  
to  
Replace handset name  
The default name is "HANDSET ". You can change the name up to a maximum of 8  
characters. To set, follow as below:  
- enter sub-menu"HANDSET" which is in the mainmenu, search for "HS NAME".  
Press  
key follow by the  
key. Delete the old name and input the new name  
using the alphanumeric keypad. (Follow the same procedure used to input name into  
the phone book). Press  
to confirm.  
Language display setting  
SD8141 is equipped with a multi language menu. To set the language between the  
available, follow as below:  
- enter sub-menu "LANGUAGE" which is in the main menu. Press  
desired language by or keys. Press to confirm.  
and select the  
RD  
 
12  
Phone book  
SD8141 can store up to 40 alphanumeric memories with name of 8 characters and  
numbers of 18 digits. To store, follow as below:  
- enter sub-menu "PHONEBOOK" which is in the main menu and select "NEW". Input  
name by the alphanumeric keypad (see table below) and press  
and press key to confirm. Escape sub-menuor store other location.  
NOTE: if there is anerror during setting, press  
. Input number  
key to delete.  
x4  
Key  
1
2
3
4
5
6
7
8
x1  
Space  
x2  
-
B
E
H
K
N
Q
U
X
x3  
1
C
F
I
L
O
R
V
Y
x5  
A
D
G
J
M
P
T
W
0
2
3
4
5
6
S
7
9
8
Z
9
0
To modify entry memory  
Select"EDIT" under the sub-menu"PHONEBOOK".  
Select the name to be modified by pressing  
or  
key. Press  
and, if  
RD  
necessary, modify the name. Press  
charactersor numbers by pressing  
and, if necessary, modify the number. Delete  
key. Press to confirm.  
To delete entry memory  
Select "DELETE" under the sub-menu "PHONEBOOK". Select the name to be deleted by  
pressing RD or keys. Press to confirm.  
To delete all entry memory  
Select"DEL ALL" under the sub-menu"PHONEBOOK". Press  
NOTE: All data relative to the phonebook will be erased.  
to confirm.  
To call entry memory  
\
Keys. To send a call press  
RD  
Press  
key and look forthename tobecalledby pressing the  
key.  
or  
To store a number from the redial numberlist  
RD  
Press  
until the LCD screen display the desired number. Press  
"SAVE? ", press and input theassociated name and press  
Key again toconfirm thenumber.  
key, look throughtheredialnumber list by pressing the RD  
or  
keys  
key, display will show  
key toconfirm, press  
To store a number fromthe caller identity, see section under"Caller Identity".  
 
13  
Alarm setting  
SD8141 is equipped with daily alarm. The alarm can be set daily but the alarm time will  
reflect the time that was set previously. The alarm duration is 30 seconds. Press any  
handset key to stop alarm. To set, follow as below:  
- enter sub-menu "HANDSET" which is in the main menu and search for "ALARM". Enter  
this sub-menu and select "ALARM TIME". Press  
minutesandpress key.  
and set hours. Press  
key. Set  
to  
Press either  
confirm.  
Repeat the last step toenable alarm every day.  
or  
and select "SET ALARM ". Set "YES " or "NO". Press  
RD  
PIN code changing  
When you perform advanced setting or subscribe to anew handset, a PIN code isused  
for the security of Tower. The default PIN code is "0000 ". To set new PIN code, follow as  
below:  
- enter sub- menu"BASE" which is in the mainmenu and search for"ADVANCED". Press  
, LCD screen will display "PIN ". Input old PIN (0000default) and press  
. Look for  
. LCD screen will display "NEW PIN", input new PIN (maximum  
key. LCD screen will display “REPEAT", input new PIN again and  
"PIN CODE " and press  
8digit)and press  
press  
toconfirm.  
Dialing mode setting  
Most of the public telephone centrals use tone (DTMF) dialling which is much more  
faster than Pulse dialling. However if your telephone line is connected to an old one,  
you will need to set Pulsedialling to dial outgoing numbers. To set, follow as below:  
- enter sub-menu"BASE" which is in the mainmenu and search for"ADVANCED". Press  
, LCD screen will display "PIN ”. Input PIN code (0000 default) and press . Look  
. Select between "TONE" and "PULSE" and press to  
for "DIAL MODE" and press  
confirm.  
Reset to default value  
In case if you need to revert to default setting, reset as follows. This will erase all  
memories and Tower will come back todefault setting.  
- enter sub-menu"BASE" which is in the mainmenu and search for"ADVANCED". Press  
, and LCD screen will display "PIN ". Input PIN code (0000 default) and press  
Look for "DEFAULT" and press . LCD screen will display "CONFIRM? ". Press  
confirm and it will returnto the default setting.  
.
to  
NOTE: With the reset, the name of the handset does not returnto the default name.  
NOTE: With the reset, the routable and special prefix are deleted, see "LCR "  
paragraph to input the defaultprefix.  
 
14  
PABX code  
To obtain an external line, the norm is to dial a ‘0’ or ‘9’ for dial tone if the unit is  
connected to a PABX. If you were to program a PABX code, there will be a pause of 3/5  
seconds between the line access code (0 or 9) and the number to be dialled out.  
When numbers are stored in the phone book, insert ‘0’ or ‘9’ as the first digit for getting  
an external line. Set as below:  
- enter sub-menu"BASE" which is in the mainmenu and search for"ADVANCED".  
Press  
Look for"PABX PAUSE" and press  
and input the desired digit(normally’ 0’ or ‘9’) andpress  
. Select between 3 and 5 seconds which is the pause time to be introduce  
automatically, press toconfirm.  
, LCD screen will display "PIN ". Input PIN code (0000 default) and press  
. LCD screen will display"PABX CODE". Press  
. Look for"PAUSE" and press  
.
Call barring  
SD8141 allows setting of 3 different levels of call barring. You can also specify which  
handset to be locked. The barring are "LOCAL" all local numbers will be blocked,  
"NATIONAL" all numbers starting with 0 will be blocked, "INTERNATIO" all numbers starting  
with 00 will be blocked. To set call barring, follow as below:  
- enter sub-menu"BASE" which is in the mainmenu and search for"ADVANCED".  
Press  
Look for "CALL BAR" and press  
, LCD screen will display"PIN ". Input PIN code (0000 default) and press  
.
. LCD screen will display "HANDSET 1". Select the  
. Now choose between “LOCAL", "NATIONAL"  
handset to be blocked and press  
and "INTERNATIO". Press  
toconfirm.  
Disabling call barring  
Enter sub-menu "CALL BAR " as described above and press  
. LCD screen will display  
. Select "NO BARRING "and  
"HANDSET 1". Choose the handset to be unlock and press  
press  
toconfirm.  
 
15  
LCR (Least Cost Routing)  
SD8141 is equipped with LCR multi carrier system. To understand the operational  
method of LCR, there is a need to deepen the routing. Programming the sub-menu  
"LCR " allows the routing of the numbers youprefer. To set, follow as below:  
-Primary: main secondary network operator towardwhich you want toroute all calls;  
- routable: stored the area code, or only the first digit of area code. It must be routed  
toward the "PRIMARY" main secondary network access code. You can store up to 5  
area code (the following area codes areset as default: 0, 00, 3and 4);  
- Special : area code that must not be routed. It is preferable to call with the main  
network without routing . Please see page 2 where the area codes set as default are  
indicated. You can store up to 10area code.  
- others : in this list, other area codes can be stored to be routed with another network  
operator.  
Please note that the area code which you wish to store here are not inside the  
"routable "list.  
NOTE: a PIN code (0000 default)is needed when you dothe programming.  
Attention  
The only way to use the LCR is to made a pre-dial. Dial a number, or recall it from any  
memory, and then press  
pressed, will not be routed.  
key to send a call. All numbers dialled after  
key is  
How to enable / disableLCR  
After programming as described below, enable (or disable if necessary) with the  
following: enter sub-menu"LCR "which is in the mainmenu and search for"YES"  
toconfirm.  
(or"NO"). Press  
Setting LCR “Primary”  
Enter sub-menu"LCR "which is in the mainmenu and search for "PRIMARY". Press  
and enter the network operator code up to maximum 6 digit (ex. 1088). Press  
confirm.  
to  
If you would like to modify the one that is previously stored, repeat the above steps.  
Makesure todeletetheold one by using  
key.  
Setting LCR “Routable”  
Enter sub-menu"LCR "which is in the mainmenu and search for"ROUTABLE". Press  
and look for “NEW”. Press  
toconfirm.  
, enter area code of maximum 6 digit and  
press  
To modify an area code: under sub-menu "ROUTABLE", select "MODIFY". Look for the  
area code to be modified and press . Using the key, delete the digit and  
enterthenewone. Press to confirm.  
To delete an area code: under sub-menu "ROUTABLE", search for "DELETE". Look for the  
areacodetobedeleted and press to confirm.  
To delete all area code stored: under sub-menu "ROUTABLE", search for "DEL ALL" and  
press toconfirm. All areacodes willbedeleted.  
 
16  
Setting LCR “Special”  
Enter sub-menu"LCR "which is in the mainmenu and search for"SPECIAL". Press  
, enterareacodeup tomaximum 6digitand press  
and look for"NEW". Press  
to confirm.  
To modify an area code: under sub-menu "SPECIAL", select "MODIFY ". Look for the area  
code to be modified and press . By using key, delete the digit and enter new  
one. Press to confirm.  
To delete an area code: under sub-menu "SPECIAL", search for "DELETE". Look for the  
areacodetobedeleted and press to confirm.  
To delete all area code stored: under sub-menu "SPECIAL", search for "DEL ALL" and  
press toconfirm. All areacodes willbedeleted.  
Setting LCR "Others "  
Enter sub- menu"LCR "which is in the mainmenu and search for “OTHERS. Press  
and look for"NEW". Press  
, enterareacodeup tomaximum 6digitand press  
, enternetworkaccess codeup tomaximum 6digitand press  
To confirm. Press  
toconfirm.  
To modify one entry: under sub-menu "OTHERS ", search for "MODIFY ". Look for the area  
code / network operator code to be modified and press  
thedigitoftheareacodetobemodified. Enter thenewdigitand press the  
. Using  
key, delete  
key.  
Delete the digit of network operator code to be modified. Enter new digit and confirm  
by pressing the key.  
To delete one entry: under sub-menu "OTHERS", search for "DELETE". Look for the area  
code/networkoperatorcodeand press to confirm.  
To delete all entry: under sub-menu "OTHERS", search for "DEL ALL" and press  
confirm. All entry will be deleted.  
to  
Multi handset configuration  
You can subscribe up to 5 handsets to the same base set.  
Subscription of optional handset  
- Press and hold the base key for about 5 seconds (two beep tone will be hear). The  
subscription will completed after 1 minute.  
- With handset: enter sub-menu "REGISTER” which is in the main menu. "BS 1 2 3 4 " will  
be displayed on the LCD screen (the numbers 1- 4 will blink, indicating that the handset  
is already subscribed at the corresponding base number). Choose the base number  
andthehandsettobesubscribed(from1to4). Press  
to confirm .  
Key in the PIN code corresponding to the base set (0000 default) and press  
. The  
handsetwillstartsearchingandthesubscriptionwillbecompletedinafewseconds.  
NOTE:repeattheaboveprocedureifitdoesnotworkthefirsttime.  
 
17  
De-subscribe an handset  
Enter sub- menu "BASE" which is in the main menu and search for"ADVANCED". Press  
,"PIN " will be displayed. Enter PIN code (0000 default) and press  
. Look for "DEL HS"  
. The LCD screen will display "HANDSET 1 ". Choose the handset to be  
and press  
deletedand press  
. "Confirm? " willbedisplayed. Press  
toconfirm.  
Attention: De-subscription could not be done with the de-subscribed handset that you  
areusing  
Intercommunicationbetweenhandsets  
With 5 handsets, you can do up to 2 intercommunications with 4 handsets and one  
handset communicating with external line simultaneously.  
To call a handset:  
1) Press INTkey and the handset number you wish to dial.  
2) The called handset will ring, press  
key to answer.  
3) Press the same key in both handsets to end a call.  
Call transfer between handsets  
1) When you are using an external line, press the INTkey (the line will be put on hold).  
2) Enter the handset number where you to wish to transfer the call.  
3) When the called handset is picked up, an intercom call will be started.  
4)Press  
key tocompletethetransfer.  
Ifthecalledhandsetrefusethecall, press INTtoobtainanexternallineagain.  
Conferencecall  
A conversation with external line can be extended to another handset. To enable the  
conference call, follow the same operation described for call transfer and when the  
intercommunication is established, press INT and #. The conference call is now  
enabled.  
Multi base configuration  
With the GAP profile, you can subscribe your handset to 4 different DECT bases (also if  
different brand and model) provided that these are of the same profile. In this mode, it  
is possible to create an area of wide coverage which, in optimal conditions, allow the  
useofahandsetfora maximumdistanceof1200m.  
 
18  
Subscribehandsettoanotherbase  
The procedure is the same as those described in "Subscription of optional handset". If  
the base where you want to subscribe the SD8141 handset is of a different model,  
please follow the instruction manual on how to put it in subscription mode. When you  
are done, follow the same procedure described in "Subscription of optional handset".  
Do the vice versa when you want to subscribe an handset of different model to the  
SD8141 base. Set the base in “subscription mode” by pressing and holding the base  
key for about 5 seconds and follow the handset subscription instruction.  
NOTE: you need to know the base PIN code where you want to subscribe one handset.  
Base search  
Sd8141 is continuously searching the base for stronger signal to be connected. If you  
want to do it manually, you will need to choose one particular base and follow the  
same operation described for the optional handset subscription without pressing the  
base key. Then handset will be connected to the selected base.  
Baby sitting (room monitor)  
With 2 SD8141 handsets, you can set one of them for room monitoring. It will answer  
automatically in the case of an internal call. This function is typically used to monitor  
children when they sleep in another room. You can set the handset to be put in the  
children room as below:  
Enter sub-menu "BABYSIT" which is in the main menu and search for ”YES”. Press key  
will be displayed). To disable, repeat the above operation  
to confirm (the symbol  
and select “NO” .  
To start monitoring, press INT key and enter the handset number with the baby call  
featureenabled. Press key toend monitoring.  
 
19  

Sharp PDAs Smartphones IQ 8900 User Manual
Shindaiwa Trimmer 82014 User Manual
Shure Headphones SRH1540 User Manual
Sony Car Stereo System CDX GT41UW User Manual
Sony DVD Recorder RDR HX710 User Manual
Sony MP3 Player D EG3 User Manual
Sony Satellite Radio Satellite Radio User Manual
Sony Speaker System SRS T70 User Manual
Southbend Convection Oven P32 NFR User Manual
Sunbeam Electric Grill HG3300 User Manual